(267) 389-9644
Old brick chimney stack on a weathered slate roof, with metal flashing where it meets the roof

Chimney Flashing Repair and Replacement

Flashing repair typically runs $300 to $1,500, and full flashing replacement $1,000 to $3,500. We find where the water actually gets in at a free leak check first.

Flashing is the metal seal where the brick meets the roof. When it fails, water shows up on the top-floor ceiling, down the wall beside the chimney or in the attic, and the roof usually gets the blame. The City's Rowhouse Manual tells owners to have a professional check the roof for blistering and cracking at flashing and chimney caps, and the Historical Commission's Diamond Street manual notes that water problems at chimneys usually start at the flashing and the chimney top.

Our weather keeps flashing busy. NOAA's normals put yearly precipitation at 42 to 52 inches across our stations, from about 42 at Lancaster's airport to nearly 51 in Center City and near West Chester. Every inch runs down the roof and hits the uphill side of the chimney first. A wide chimney with nothing behind it to split the flow collects water and debris there, and that is where many of the leaks we trace begin.

When to call

  • A wet patch on the plaster right next to the chimney
  • Drips in the attic along the chimney during heavy rain
  • Flashing lifted, rusted or buried under layers of tar
  • The mortar joint holding the counter flashing has opened up
  • A leak that gets worse in wind-driven rain or melting snow

The visit, step by step

  1. Free leak checkWe look at the flashing, crown, joints and cap, inside and out, to find where the water gets in.
  2. Repair or replaceLoose or short sections are reset or replaced; failed flashing is stripped back to sound material.
  3. Step and counter flashingNew step flashing is worked in with the roofing; counter flashing is set into a cut mortar joint.
  4. Cricket if neededOn a chimney wider than 30 inches, a cricket goes in behind it, priced at the inspection.

Is it the flashing, or something else?

Plenty of leaks blamed on flashing come from higher up: a cracked crown or open mortar joints let water into the brick, where it runs down inside the chimney and appears at the roofline. Re-flashing a chimney like that changes nothing. So the free check covers the crown, the cap and the joints as well as the metal.

If the flashing is the problem, we show you where and how. A loose piece of counter flashing or a short run of failed sealant is a repair, typically $300 to $1,500. Flashing that is rusted, torn or buried in tar all the way around usually means replacement, typically $1,000 to $3,500.

Crickets on wide chimneys

Current code, the 2021 IRC used in Pennsylvania since January 1, 2026, calls for a cricket on the uphill side of a chimney wider than 30 inches, measured parallel to the ridge. A cricket is a small peaked roof that splits the water around the chimney instead of letting it pond against the brick. Many older chimneys on Main Line houses and Bucks County stone homes are wider than that and have none.

Adding one usually means opening the roofing behind the chimney, so it is priced at the inspection along with the flashing work that goes with it.

Rowhouse roofs, tar patches and historic properties

On many Philadelphia rowhouses the chimney rises from a low-slope roof, and the base of the stack has been patched with layer after layer of roof coating. Each new layer hides the last, and water finds the seams. We strip back to sound material before setting new flashing, and we work around your roofer where the roof itself needs attention.

On a designated Philadelphia property, reroofing counts as an alteration under the Historical Commission's rules, so flashing work tied to a reroof goes through review. Elsewhere we check what your city, township or borough requires before starting.

Answers

Chimney Flashing Repair questions

How do I find where my chimney is leaking?

Note when it leaks. A leak only in wind-driven rain often points to the flashing or the brick on the windward side; a leak as snow melts often points to the crown or flashing. Our free leak check looks at all of it, inside and out.

Roofer or chimney company: who fixes a flashing leak?

Either can fix flashing. The advantage of a chimney check is that we also look at the crown, cap and mortar, which cause many leaks that only look like flashing leaks.

Can flashing just be sealed with tar?

Tar buys a season at best and hides the real problem. Counter flashing should be set into the mortar joint, with step flashing woven into the roofing.

Do I need a cricket behind my chimney?

Current code calls for one when the chimney is wider than 30 inches parallel to the ridge. If yours is wide and leaks on the uphill side, a cricket is often the fix. It is priced at the inspection.

How much does flashing repair cost?

Repairs typically run $300 to $1,500. Full replacement typically runs $1,000 to $3,500.

Rooftops of brick row houses in the foreground with the Center City Philadelphia skyline behind, on a sunny day

Schedule

Choose a morning or an afternoon.

Sunday through Friday, arrival between 8 and 11, 11 and 2, or 2 and 5. The look costs nothing, and a person phones you the day before.

Or call (267) 389-9644

Call (267) 389-9644