
Gas Fireplace Won't Start or Keeps Going Out
Most gas fireplace failures come down to a few worn parts: the igniter, the pilot assembly, the thermocouple or the gas valve. Diagnosis is free; installed parts typically run $90 to $350.
Philadelphia runs on gas. The Census counts about 70 percent of the city's homes heating with utility gas, and in Drexel Hill and Haverford Township the share passes 75 percent. Gas fireplaces and log sets are common in all of them, and they tend to get attention only when they quit, usually on the first cold evening of fall.
When a gas fireplace won't start or keeps shutting off, the cause is usually a small part in the pilot system that has worn out or clogged. Sometimes, though, the symptom points to a venting problem, and that one is about safety, not comfort. A good repair visit covers both: the part that failed, and why.
When to call
- Pilot refuses to catch, or dies once the knob is released
- Clicking with no flame
- Burner lights, then shuts off after a few minutes
- Lazy, yellow flames or soot on the glass
- A gas smell near the unit (leave and call the utility first)
The visit, step by step
- Diagnose, freeWe test the ignition, pilot, flame sensor and valve, and look at the vent, before replacing anything.
- Price the part in writingYou see which part failed and what it costs installed before we fit it.
- Repair and clear the pilotThe failed part is replaced, pilot and burner ports are cleared, and logs or media go back in their proper positions.
- Test a full cycleWe run the fireplace from cold through a full burn and check the flame and the vent.
Why it won't light or stay lit
A standing-pilot gas fireplace depends on a small flame heating a sensor. If the sensor doesn't feel that heat, the valve shuts off the gas for safety. Most no-heat calls trace back to one of these parts, with typical installed prices from HomeGuide's 2026 fireplace repair data:
- Igniter, the spark button or electronic igniter that lights the pilot: $90 to $150.
- Pilot assembly, the pilot burner, hood and orifice, which clog with dust and spider webs: $100 to $350.
- Thermocouple, the small sensor that confirms a pilot flame to the valve: $150 to $350.
- Gas valve, the control that meters gas to the pilot and burner: $150 to $300.
When the problem is the vent, not the part
A burner that lights and then shuts down can be a safety sensor tripping because exhaust is not leaving the way it should. On a direct-vent unit, a crushed or disconnected vent pipe, or a blocked termination outside, can do it. With gas logs in a masonry fireplace, the cause may be a blocked flue, a nest, or a chimney that ended up too low after construction next door. UGI warns that a damaged or blocked chimney can let exhaust, including carbon monoxide, into a home, and Philadelphia L&I says an obstructed chimney raises the risk of CO poisoning. We check the vent on every repair for that reason.
Where a vented gas appliance connects to a masonry chimney, the 2021 IRC (G2427.5.5) asks that the passage be examined first, and cleaned if it once vented wood or oil.
Gas smell or CO alarm: call the utility first
Smell gas? Get out first, then phone from the sidewalk. In Philadelphia that is PGW at 215-235-1212, around the clock. PECO's emergency line is 800-841-4141, and PECO asks you to get at least 100 feet away first. UGI customers call 800-276-2722 or 911. Don't flip switches, use a phone indoors or try to close valves yourself. If a CO alarm sounds and anyone feels ill, call 911. After the utility clears the house, we can work out what is wrong with the fireplace.
Answers
Gas Fireplace Repair questions
Why does my gas fireplace keep going out?
Usually a dirty or weak pilot flame that no longer heats the thermocouple enough, or a thermocouple near the end of its life. A blocked vent can cause the same shutdowns, which is why we check both.
The pilot burns, yet the main flame never starts. What's wrong?
Common causes are a worn thermopile or thermocouple, a wall switch or remote that has failed, or a gas valve that is sticking. We test each in turn and price the part before replacing anything.
Will the gas fireplace work when the power is out?
It depends on the ignition. Many units with a standing pilot keep working without house power, while electronic-ignition models may need batteries or electricity. Your manual will say which you have, and we can show you at a visit.
Why is the glass on my gas fireplace turning black?
Black soot usually means logs or media out of position, a dirty burner or a poor air mix. It is a sign the fireplace needs service, not just a glass cleaning, so stop using it until it is checked.
There is a gas smell by the fireplace. Who do I phone?
Your gas utility, from outside the house: PGW 215-235-1212 in Philadelphia, PECO 800-841-4141, or UGI 800-276-2722. Call us once they have made the house safe.
Schedule
Choose a morning or an afternoon.
Sunday through Friday, arrival between 8 and 11, 11 and 2, or 2 and 5. The look costs nothing, and a person phones you the day before.
